Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
Each person may have their personal rationale on the subject of A Step-by-Step Guide to Installing a Bathtub.
Mounting a tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and also often, tiling abilities. Changing an old bathtub with a new one is additionally a moderately difficult job. If the old tub is readily obtainable, the job can move immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually qualified on your own for the job as well as are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This post will assist you install a new tub in your washroom if you have actually already gotten a brand-new tub and do not require to change the plan of your previous water pipes.
Your tools and also material checklist need to comprise the following:
Getting ready for the Installation
Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be quite troublesome due to the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water system as well as check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill the tub as well as likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait up until the bath tub has been made use of a minimum of once as this will certainly resolve it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in location between the faucet and also the sink. Protect the tap in position with the producer given backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, causing the water to penetrate the wall in between the bath as well as the tiling, resulting in problems with moisture and possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as installations. They are marketed in tubes as well as cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in usage. The sealer can crack rather very early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the tiles making use of waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about Installing A Bathtub? Write a short review directly below. We would be pleased to see your reactions about this piece. We hope that you visit us again soon. I beg you take the opportunity to share this write-up if you appreciated it. Thanks a bunch for your time. Kindly check our website back soon.
Schedule And Pricing Report this page